How to measure your wall
All we need is the exact width and height of your wall. There is no trim allowance to work out: we add the extra for trimming to every edge ourselves, free. Ten minutes with a tape measure, and the pictures below show the common wall shapes, awkward ones included.


Two numbers, ten minutes
- 1Measure the width in three places — near the ceiling, in the middle and just above the baseboard — and keep the largest.
- 2Measure the height at the left, in the middle and at the right, and keep the largest.
- 3Enter those two numbers exactly as you measured them. Do not add anything: we add the extra for trimming to every edge ourselves, free.
Enter them on any design's page, in inches, feet or centimeters, and the price appears.
Choose a designWhat you need

A tape measure, a pencil and something to write on — and a step ladder if the wall is taller than you can reach. Ten minutes is plenty.
Measure the width three times
Corner to corner, near the ceiling, at waist height and just above the baseboard. Keep the tape level: a sagging tape reads long.
Keep the largest of the three. Walls are rarely square. If the wall is wider at the top and you order the bottom figure, the top corners come up short — and short cannot be fixed, while a little extra is trimmed off in seconds.
Measure the height three times
At the left, in the middle and at the right, from the top of the baseboard to the ceiling. Keep the largest.
If you are taking the baseboard off and refitting it over the paper, measure to the floor instead. Decide before you measure.
Give us the exact size — we add the extra
Many people try to work out a trim allowance before they order. There is no need: we add it. Every panel is printed with extra on each edge, free — you pay for the wall you measured, not the margin — so the panels arrive slightly larger than the wall and you cut the surplus away once they are up.
Add your own margin and you pay for paper you throw away, a scenic design can shift off center, and the panel count can tip over by one. The exact size of the wall is all we need.
Doors and windows
Measure the whole wall as if they were not there, and order that size. Hang the panels straight over the opening and cut it out afterward with a sharp blade.
It feels wasteful and it is the right answer every time: cutting a shape out before hanging almost never lines up.
Sloped ceilings, gables and stairwells
Order the rectangle that contains the slope: the widest point by the tallest point. On a gable wall that rises to a peak in the middle, the tallest point is the peak. Hang the panels, then trim along the angle in place against a straight edge.
Two or more walls
Measure each wall exactly, add the widths together and use the tallest height: a 7 ft wall and a 10 ft wall, both 8 ft high, are ordered as one mural 17 ft wide and 8 ft high. Give us those exact figures, with nothing added. We print one continuous mural with a trim allowance on every edge, and set up the print from there.
If you would rather each wall showed its own crop of the design, order the walls separately.
Check your numbers
Multiply the width by the height in feet: a ten by eight foot wall is 80 square feet. If your sum says 960, you have multiplied inches by feet somewhere: 120 inches times 8 feet.
Ceilings are measured the same way — three readings each way, keep the largest — with two people on the job.
Before you order
- Look at the preview. On a product page, "Your wall" shows the real crop of the artwork at your size. Move it there if a horizon or a focal point lands somewhere strange.
- Not sure about your numbers? Send us a few photos of the wall and a rough sketch with your measurements on it: a pencil drawing on paper is plenty. Email them to hello@wallbu.com and we will tell you exactly what to enter, before you order.
A sloped ceiling, a fireplace wall, a window in the middle of the wall: anything awkward is exactly what the photos and the sketch are for. We take it from there.
Not sure about a wall?
Send us your numbers and a photo. We would rather answer a question than reprint a mural.
Common questions
Measure the width in three places, at the floor, at mid height and near the ceiling, and use the largest number. Do the same for the height, at the left edge, the middle and the right edge. Walls are rarely square, so the largest measurement is the one that guarantees full coverage. Enter those two numbers exactly as you measured them, in inches or centimeters: there is no trim allowance to work out, because we add the extra for trimming ourselves.
No, give us the finished wall size and nothing more. Every panel is printed with a trim allowance on each edge, free — you pay for the wall, not the margin — so your panels arrive slightly oversized and you cut the surplus away against the ceiling, baseboard and corners after hanging. Adding your own margin on top means you pay for material you will throw out, and it can push a design off center.
Murals are printed to the size you enter, so there is no fixed design width to run out of. Scenic designs are cropped and scaled to your ratio, and the configurator preview shows exactly which part of the artwork lands on your wall. Repeating patterns simply tile further across. If a crop cuts something you care about, adjust the frame in the configurator or write to us.
No. Measure the full rectangle of the wall as if the opening were not there, order that size, and cut the opening out after the panels are on the wall. That keeps the design continuous above and beside the door or window, which is what makes a mural read as one image. Cutting around an opening on paper before hanging almost always shifts the alignment.
Yes. Measure each wall exactly, add the widths together and use the tallest height: a 7 ft wall and a 10 ft wall, both 8 ft high, are one mural 17 ft wide and 8 ft high. Give us those exact figures with nothing added; we print one continuous mural with a trim allowance on every edge. If you would rather each wall showed its own crop of the design, order the walls separately instead.
Order the full rectangle that contains the sloped or stepped area and trim the angle in place with a sharp blade and a straight edge. For stairwells, measure the highest point and the widest point of the wall. Ceilings are measured the same way as walls, though a second pair of hands is close to essential. Send us a photo if you want us to check the crop first.
Last updated October 4, 2026.
